The perfect choice for professional players looking for the ultimate bass amplifier.
The WTP900 offers a ground-shaking 900W of power and is built to tour - meaning the legendary EDEN sound comes with advanced cooling and ventilation, in a tough steel chassis.
The WTP delivers professional tone and features for the touring musician in the studio and on the road.
Plug your active or high output bass in here.
Plug your passive or low output bass here.
Press this switch to mute and un-mute the amplifier. When the amplifier is muted the light will illuminate. This indicator also features on the optional foot controller.
A studio quality, high speed, soft knee compressor which allows you to easily achieve the right level and amount of compression required for your playing style. The compressor acts quickly and adjusts its compression dependent on where in the register notes are played.
Adjust the low frequencies of the amplifier using this
control.
World Tour Pro amplifiers are supplied with rack ears already fitted, meaning it's ready to securely mount in to a rack straight out of the box.
Turn the unit on or off.
Controls the overall volume of your amplifier. Use this control in conjunction with the output clip indicators to achieve the best performance from your amplifier.
30-300Hz: Use this control to choose the frequency to be adjusted by the Low control.
World Tour Pro Amplifiers stay cool under pressure, even in racks, thanks to an advanced and powerful cooling system.
This light will illuminate when the EQ stage of the amplifier is clipped.
Illuminates when unit is switched on.
Fine tune the amount of signal sent to the preamp using this control.
The Enhance circuit provides an easy-to-use EQ sweep, allowing you to simultaneously boost very low bass, upper middle and high frequencies, while cutting the lower mid frequencies. Quickly find your sound before adjusting the finer EQ details.
Adjust the amount of lower mid frequency applied using this control, set at 0 the response will be flat. Use in conjunction
with the 30-300 Hz control to define where in the lower mid frequency changes are made.
Adjust the amount of upper mid frequencies applied using this control, set at 0 the response will be flat. Use in conjunction with the 1.2Khz-12Khz control to define where in the upper mid frequency changes are made.
Adjust the amount of mid frequencies applied using this control, set at 0 the response will be flat. Use in conjunction with the 200hz-2Khz control to define where in the mid frequency changes are made.
200Hz-2KHz: Use this control to choose the frequency to be adjusted by the Mid control.
1.2KHz-12KHz: Use this control to choose the frequency to be adjusted by the High control.
Increase or decrease the amount of treble applied here, set at 0 the treble response will be flat.
World Tour Pro amplifiers are supplied with rack ears already fitted, meaning it's ready to securely mount in to a rack straight out of the box.
The World Tour Pro uses 2 tubes in its design. The first tube provides signal control as used in many of Eden’s traditional amplifiers. The second tube is used entirely to provide additional warmth and produce a more driven and aggressive sound without losing definition.
Plug your supplied power cord into your Eden amplifier using this mains inlet socket.
This fan is just one of many features that keep World Tour Pro amplifiers cool.
World Tour Pro Amplifiers stay cool under pressure, even in racks, thanks to an advanced and powerful cooling system.
The Eden Illuminated Output System used on World Tour Pro amplifiers has been designed by Eden to more easily
allow players to make the right choices with their rig selection, even in the dark. Depending on selected mode, connect the correct impedance cabinet here using a Speakon speaker lead here.
Connect an external device, such as an MP3 player, here using a 3.5mm jack cable.
Connect your headphones here using standard 3.5mm headphone cable.
Connect your optional foot controller here.
Turn crossover circuit off or on using the X Over switch.
Use the X Over Control to adjust the crossover point between each amplifier and the Left/Right line level outputs (Bi-Amp mode only).
Connect to either a mixing desk, front of house system or recording device using a standard XLR cable. Adjust the output level of the DI signal with the DI Volume control.
Lift ground from your signal (when required) using this switch.
Select where the DI output signal is taken from here.
Take your tuner signal out from this socket.
Use this control to balance the level between the two amplifiers.
Switch between bridge mode and stereo mode here.
Cycle between available speaker output settings using this switch.
Take/return your signal from before the EQ stage here.
Send/return your signal to/from external equipment such as effects pedals.
| Power Handling: | 900W @ 8Ω Mono (450W x2), Stereo 450W per side in to 4Ω |
|---|---|
| Amp Modes: | Stereo and bridgeable |
| Freq. Response: | 10Hz - 15KHz |
| Speaker Connection: | Speakon |
| Dimensions: | H: 3.5 in / 8.8 cm W: 16.9 in / 43 cm D: 15.75 in / 40 cm |
| Weight: | 34.1 lbs / 15.5 kgs |
- 450 Watts RMS per side at 4Ω, 900 watts at 8Ω in Bridged mode
- 5-Band EQ section with sweepable low mid, mid and high mid controls
- Enhance control
- Super-fast compression with Amount and Ratio controls
- Tube warmer circuit
- Pre-EQ loop
- Stereo post-EQ loop
- DI output
- 3.5mm Aux in & Headphone out
- Electronic Crossover
